トップ調べ方案内科学技術・医学専門資料規格>ISO Handbook "Limits, fits and surface properties" の収載規格一覧

ISO Handbook "Limits, fits and surface properties" の収載規格一覧

ISO Handbook "Limits, fits and surface properties"国立国会図書館の所蔵情報へのリンク(2nd ed. International Organization for Standardization 1999 【当館請求記号:M361-B40】)に収載されているISO規格は以下のとおりです。

Part 1: Terminology

ISO 4287:1997 Geometrical Product Specifications (GPS) -- Surface texture: Profile method -- Terms, definitions and surface texture parameters 
ISO 6318:1985 Measurement of roundness -- Terms, definitions and parameters of roundness
ISO 8785:1998 Geometrical Product Specification (GPS) -- Surface imperfections -- Terms, definitions and parameters

Part 2: Limits and fits

Part 2.1 General limits and fits

ISO 1:1975 Standard reference temperature for industrial length measurements
ISO 286-1:1988 ISO system of limits and fits -- Part 1: Bases of tolerances, deviations and fits
ISO 286-2:1988 ISO system of limits and fits -- Part 2: Tables of standard tolerance grades and limit deviations for holes and shafts
ISO 370:1975 Toleranced dimensions -- Conversion from inches into millimetres and vice versa
ISO 1119:1998 Geometrical Product Specifications (GPS) -- Series of conical tapers and taper angles
ISO 1829:1975 Selection of tolerance zones for general purposes
ISO/R 1938:1971 ISO system of limits and fits -- Part II: Inspection of plain workpieces
ISO 2538:1998 Geometrical Product Specifications (GPS) -- Series of angles and slopes on prisms
ISO 2768-1:1989 General tolerances -- Part 1: Tolerances for linear and angular dimensions without individual tolerance indications
ISO 2768-2:1989 General tolerances -- Part 2: Geometrical tolerances for features without individual tolerance indications
ISO 8062:1994 Castings -- System of dimensional tolerances and machining allowances
ISO 13920:1996 Welding -- General tolerances for welded constructions -- Dimensions for lengths and angles -- Shape and position
ISO/TR 14638:1995 Geometrical product specification (GPS) -- Masterplan

Part 2.2: Limits and fits for screw threads

ISO 7-1:1994 Pipe threads where pressure-tight joints are made on the threads -- Part 1: Dimensions, tolerances and designation
ISO 7-2:1982 Pipe threads where pressure-tight joints are made on the threads -- Part 2: Verification by means of limit gauges
ISO 228-1:1994 Pipe threads where pressure-tight joints are not made on the threads -- Part 1: Dimensions, tolerances and designation
ISO 228-2:1987 Pipe threads where pressure-tight joints are not made on the threads -- Part 2: Verification by means of limit gauges
ISO 965-1:1980 ISO general purpose metric screw threads -- Tolerances -- Part 1: Principles and basic data
ISO 965-2:1980 ISO general purpose metric screw threads -- Tolerances -- Part 2: Limits of sizes for general purpose bolt and nut threads -- Medium quality
ISO 965-3:1980 ISO general purpose metric screw threads -- Tolerances -- Part 3: Deviations for constructional threads
ISO/R 1501:1970 ISO miniature screw threads
ISO 1502:1996 ISO general-purpose metric screw threads -- Gauges and gauging
ISO 2903:1993 ISO metric trapezoidal screw threads -- Tolerances
ISO 5864:1993 ISO inch screw threads -- Allowances and tolerances

Part 2.3 Limits and fits for gears and involute splines

ISO 1328-1:1995 Cylindrical gears -- ISO system of accuracy -- Part 1: Definitions and allowable values of deviations relevant to corresponding flanks of gear teeth
ISO 1328-2:1997 Cylindrical gears -- ISO system of accuracy -- Part 2: Definitions and allowable values of deviations relevant to radial composite deviations and runout information
ISO 4156:1981 Straight cylindrical involute splines -- Metric module, side fit -- Generalities, dimensions and inspection
ISO 4156:1981/Amd.1:1992 Amendment 1:1992 to ISO 4156:1981 Section three: Inspection
ISO 4468:1982 Gear hobs -- Single start -- Accuracy requirements

Part 3: Properties of surfaces

ISO 3274:1996 Geometrical Product Specifications (GPS) -- Surface texture: Profile method -- Nominal characteristics of contact (stylus) instruments
ISO 4288:1996 Geometrical Product Specifications (GPS) -- Surface texture: Profile method -- Rules and procedures for the assessment of surface texture
ISO 4291:1985 Methods for the assessment of departure from roundness -- Measurement of variations in radius
ISO 4292:1985 Methods for the assessment of departure from roundness -- Measurement by two- and three-point methods
ISO 5436:1985 Calibration specimens -- Stylus instruments -- Types, calibration and use of specimens
ISO 11562:1996 Geometrical Product Specifications (GPS) -- Surface texture: Profile method -- Metrological characteristics of phase correct filters
ISO 12085:1996 Geometrical Product Specification (GPS) -- Surface texture: Profile method -- Motif parameters
ISO 13565-1:1996 Geometrical Product Specification (GPS) -- Surface texture: Profile method; Surfaces having stratified functional properties -- Part 1: Filtering and general measurement conditions
ISO 13565-2:1996 Geometrical Product Specification (GPS) -- Surface texture: Profile method; Surfaces having stratified functional properties -- Part 2: Height characterization using the linear
material ratio curve

 

関連する「調べ方案内」

  • 国立国会図書館
  • 国立国会図書館オンライン
  • 国立国会図書館サーチ
  • 国立国会図書館デジタルコレクション
  • ひなぎく
  • レファレンス協同データベース
  • 本の万華鏡
  • 参考書誌研究